Frequency converter with direction and synchronization monitor KFD2-UFT-Ex2.D

2-channel isolated barrier
24VDC power supply (power bus)
Dry contact or NAMUR inputs
Input frequency 1 MHz ... 1 kHz
Current output 0/4 mA ... 20 mA
Relay contact and transistor output
Overriding the launch
Configurable using PACTware or keyboard
Line Fault Detection (LFD)

Ask a question

Description
Additionally

Description

Technical specifications of the KFD2-UFT-Ex2.D

Main Features
Signal type		Digital input
Supply
Connection		terminals 23+, 24- or power module/power bus
Nominal voltage		20 ... 30 V DC
Rated current		approx. 130 mA
Power dissipation		2.2 W
Power consumption		2.5 W
Interface
Programming interface		programming connector
Entrance
Connection side		side of the field
Connection		input I: terminals 1+, 3- input II: terminals 4+, 6- input III: terminals 13+, 14- (control input 1) input IV: terminals 15+, 14- (control input 2)
Entrance I, II		2-wire sensor, sensor according to EN 60947-5-6 (NAMUR) or mechanical contact
	Open circuit voltage/short circuit current	8.2 V / 10 mA
	Pulse duration	min. 250 µs, rotation direction signal overlap: ≥ 125 µs
	Input frequency	rotation direction control 0.001 ... 1000 Hz slip control 10 ... 1000 Hz
	Line fault detection	open circuit I ≤ 0.15 mA; short circuit I > 6.5 mA
Entrance III, IV
	Active passive	I > 4 mA (min. 100 ms) / I < 1.5 mA
	Open circuit voltage/short circuit current	18 V / 5 mA
Exit
Connection side		control side
Connection		output I: terminals 10, 11, 12 output II: terminals 16, 17, 18 output III: terminals 19+, 20- output IV: terminals 21+, 20- output V: terminals 7-, 8+
Exit I, II		signal, relay
	Contact loading	253 VAC / 2 A / cos φ ≥ 0.7; 40 VDC / 2 A
	Mechanical life	5 x 10 ⁷ switching cycles
	On/Off Delay	OK. 20ms / approx. 20 ms
Exit III and IV		signal, electronic output, passive
	Contact loading	40 V DC
	Signal level	1-signal: (external voltage) - 2.5V max. for 10mA or 3V max. for 100mA (100mA, short-circuit protection) -2.5V (50mA, short-circuit/overload protection) 0-signal: off (off-state current ≤ 10 μA)
Exit B		analogue
	Current range	0...20 mA or 4...20 mA
	Open circuit voltage	Max 24V DC
	Load	Max. 650 Ohm
	Malfunction signal	lower limit I ≤ 3.6 mA, upper limit I ≥ 21.5 mA (according to NAMUR NE43)
Collective error message		Power bus
Transmission characteristics
Entrance I and II
	Measurement range	0.001...1000 Hz
	Permission	slip control: 1% frequency measurement: 0.1% of the measured value; but >0.001 Hz
	Accuracy	slip control: 1% frequency measurement: 0.5% of the measured value; but >0.001 Hz
	Measuring time	frequency measurement: < 100 ms
	The influence of ambient temperature	0.003%/K (30 ppm)
Exit I, II
	Delayed response	≤ 200 ms
Exit B
	Permission	< 10 μA
	Accuracy	< 30 μA
	The influence of ambient temperature	0.005%/K (50 ppm)
Galvanic isolation
Input I, II/other circuits		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V _eff.
Input III, IV/power and collective error		Functional insulation according to IEC 62103, rated insulation voltage 50 V, _eff.
Output I, II/other circuits		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V _eff.
Mutual output I, II, III		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V _eff.
Mutual output I, II, IV		reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V _eff.
Output III, IV/power supply and collective error		basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 V _eff.
Output III, IV/Input III, IV		basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 V _eff.
Exit III, IV/V		basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 V _eff.
Output voltage/power supply and overall error		Functional insulation according to IEC 62103, rated insulation voltage 50 V, _eff.
Interface/power and general error		Functional insulation according to IEC 62103, rated insulation voltage 50 V, _eff.
Interface/output III, IV		basic insulation according to IEC/EN 61010-1, rated insulation voltage 50 V _eff.
Indicators/settings
Display elements		LEDs, display
Controls		Control Panel
Configuration		using the control buttons using PACTware
Marking		marking space at the front
Compliance with the directive
Electromagnetic compatibility
	Directive 2014/30/EU	EN 61326-1:2013 (industrial premises)
Low voltage
	Directive 2014/35/EU	EN 61010-1:2010
Correspondence
Electromagnetic compatibility		NE 21:2006
Degree of protection		IEC 60529:2001
Entrance		EN 60947-5-6:2000
Environmental conditions
Ambient temperature		-20 ... 60 °C (-4 ... 140 °F)
Mechanical characteristics
Degree of protection		IP20
Connection		screw terminals
weight		300 g
Dimensions		40 x 119 x 115 mm (1.6 x 4.7 x 4.5 in) (W x H x D), case type C2
Installation		on a 35 mm DIN rail in accordance with EN 60715:2001
Data for use in hazardous areas
EU Type Examination Certificate		TUV 99 ATEX 1471
	Marking	II (1)G [Ex ia Ga] IIC II (1)D [Ex ia Da] IIIC I (M1) [Ex ia Ma] I
Supply
	Maximum safe voltage	40 VDC (Note: U _m is not the nominal voltage.)
Entrance I and II		terminals 1+, 3-; 4+, 6-: Ex ia
	Voltage U _o	10.1 V
	Current I _o	13.5 mA
	Power P _o	34 mW (linear characteristic)
Entrance III and IV		terminals 13+, 14-; 15+, 14- are not intrinsically safe
	Maximum safe voltage U _m	40 V (Note: U _m is not the nominal voltage.)
Exit I, II		terminals 10, 11, 12; 16, 17, 18 are not intrinsically safe
	Maximum safe voltage	253 V (Caution! Nominal voltage may be lower.)
	Contact loading	253VAC/2A/cos φ>0.7; 40VDC/2A resistive load
Exit III and IV		terminals 19, 20, 21 are not intrinsically safe
	Maximum safe voltage U _m	40 VDC (Note: U _m is not the nominal voltage.)
Exit B		terminals 8+, 7- are not intrinsically safe
	Maximum safe voltage U _m	40 VDC (Note: U _m is not the nominal voltage.)
Interface		232 rupees
	Maximum safe voltage	40 V (Note: U _m is not the nominal voltage.)
Certificate		TUV 02 ATEX 1885 X
	Marking	II 3G Ex nA nC IIC T4 Gc
Exit I, II
	Contact loading	50VAC/2A/cos φ>0.7; 40VDC/2A resistive load
Galvanic isolation
	Input I, II/other circuits	safe electrical insulation in accordance with IEC/EN 60079-11, peak voltage 375 V
Compliance with the directive
	Directive 2014/34/EU	EN 60079-0:2012+A11:2013, EN 60079-11:2012, EN 60079-15:2010
International certificates
FM approval
	Control drawing	16-538FM-12
UL approval		E223772
IECEx certification
	IECEx Certificate	IECEx TUN 04.0007 IECEx TSA 18.0007X
	IECEx marking	[Ex ia Ga] IIC, [Ex ia Da] IIIC, [Ex ia Ma] I Ex ec nC IIC T4 Gc

Additionally

All products on the website are original and imported into the Republic of Kazakhstan in compliance with all laws and regulations, and only with the appropriate certificates.

Back to list