- 2-channel signal generator
- Power supply 115/230 VAC
- 3-wire PNP/NPN sensor or push-pull input
- Relay contact output
- Selectable DIP switch functions
- Minimum/maximum control
- Up to SIL 2 in accordance with IEC/EN 61508 / IEC/EN 61511
Peripherals and components
- 1-channel signal generator
- Power supply 230 V AC
- Level sensor input
- Setting range 1 kOhm ... 150 kOhm
- Relay contact output
- Fault relay contact output
- Adjustable time delay up to 10 sec
- Minimum/maximum control
- Line Fault Detection (LFD)
- 1-channel signal generator
- Power supply 230 V AC
- Level sensor input
- Setting range 5 kOhm ... 150 kOhm
- Relay contact output
- Minimum/maximum control
- 2-channel signal generator
- 24VDC power supply (power bus)
- Dry contact or NAMUR inputs
- 2 passive transistor outputs
- Reversible operation mode
- Line Fault Detection (LFD)
- Case width 12.5 mm
- Up to SIL 2 (SC 3) in accordance with IEC/EN 61508
- 1-channel signal generator
- 24VDC power supply (power bus)
- Dry contact or NAMUR input
- 2 passive transistor outputs
- Can be used as a signal splitter (1 input and 2 outputs)
- Reversible operation mode
- Line Fault Detection (LFD)
- Case width 12.5 mm
- Up to SIL 2 (SC 3) in accordance with IEC/EN 61508
- Crate for K-system
- Replacing the E-System subrack
- Max 33 insulator slots
- Short design (installation depth 211 mm)
- Connection via distribution panels
- Partial and combined assembly is possible
- Complete electrical wiring according to customer requirements
- Allows you to preserve cable routing in the distribution cabinet
- No structural changes to the distribution cabinet are required.
- Crate for K-system
- Replacing the E-System subrack
- Max 33 insulator slots
- Short design (installation depth 211 mm)
- Connection via terminal blocks
- Partial and combined assembly is possible
- Complete electrical wiring according to customer requirements
- Allows you to preserve cable routing in the distribution cabinet
- No structural changes to the distribution cabinet are required.
- Crate for K-system
- Replacing the E-System subrack
- Max 33 insulator slots
- Long design (installation depth 300 mm)
- Connection via distribution panels
- With a middle sheet and cable channel
- Partial and combined assembly is possible
- Complete electrical wiring according to customer requirements
- Allows you to preserve cable routing in the distribution cabinet
- No structural changes to the distribution cabinet are required.
- Crate for K-system
- Replacing the E-System subrack
- Max 33 insulator slots
- Long design (installation depth 300 mm)
- Connection via distribution panels
- Partial and combined assembly is possible
- Complete electrical wiring according to customer requirements
- Allows you to keep the cable routing in the distribution cabinet
- No structural changes to the distribution cabinet are required.
- 1-channel isolated barrier
- 24VDC power supply (power bus)
- Load cell input (full or half bridge)
- Output 0 mA ... ± 20 mA or 0 V ... ± 10 V
- 2 relay contact outputs
- Programmable high/low alarm
- Configurable using PACTware or keyboard
- RS-485 interface
- Low response time
- Line Fault Detection (LFD)
- 1-channel
- 24VDC power supply (power bus)
- Potentiometer input
- Output voltage 0 V ... 10 V
- Accuracy 0.05%
- Up to SIL 2 in accordance with IEC/EN 61508
- 1-channel
- 24VDC power supply (power bus)
- Potentiometer input
- Current output 0 mA ... 24 mA
- Accuracy 0.05%
- Up to SIL 2 in accordance with IEC/EN 61508
- 1-channel isolated barrier
- 24VDC power supply (power bus)
- Potentiometer input
- Current output 0 mA ... 20 mA
- Lead resistance compensation adjustment
- Accuracy 0.05%
- Up to SIL 2 in accordance with IEC/EN 61508
- 2-channel isolated barrier
- 24VDC power supply (power bus)
- Thermocouple, RTD, potentiometer, or voltage input
- Can be used as a signal splitter (1 input and 2 outputs)
- Voltage output 0/1 V ... 5 V
- PACTware is configured
- Line Fault (LFD) and Sensor Burnout Detection
- Up to SIL 2 in accordance with IEC/EN 61508 / IEC/EN 61511
- 1-channel isolated barrier
- 24VDC power supply (power bus)
- Potentiometer input
- Output voltage 0 V ... 5 V
- Lead resistance compensation adjustment
- Accuracy 0.05%
- Up to SIL 2 in accordance with IEC/EN 61508